Authors

Dwi Basuki Wibowo

Department of Mechanical Engineering, Faculty of Engineering, Universitas Diponegoro, Semarang, Indonesia

Toni Prahasto

Department of Mechanical Engineering, Faculty of Engineering, Universitas Diponegoro, Semarang, Indonesia

Ismoyo Haryanto

Department of Mechanical Engineering, Faculty of Engineering, Universitas Diponegoro, Semarang, Indonesia

Ojo Kurdi

Department of Mechanical Engineering, Faculty of Engineering, Universitas Diponegoro, Semarang, Indonesia

Khoirul Dimas Veri Anjaswara

Department of Mechanical Engineering, Faculty of Engineering, Universitas Diponegoro, Semarang, Indonesia

Abstract

Riveted joints are still widely used in steel structures because of their good resistance to mechanical loading, and their performance is governed by the joint type and the rivet geometric configuration. This study investigates the effects of joint type (lap joint and butt joint) and rivet configuration (chain pattern and zig-zag pattern) on the mechanical behavior of AISI 1020 steel riveted joints through experimental and numerical approaches. Tensile tests were carried out using a Universal Testing Machine (UTM), while stress and deformation were simulated using ANSYS Workbench based on the Finite Element Method (FEM). The zig-zag pattern produced a higher ultimate tensile strength (UTS) than the chain pattern for both joint types: 192.02 MPa versus 186.32 MPa for the lap joint (about 3.06% higher maximum load) and 196.50 MPa versus 188.80 MPa for the butt joint. The butt joint carried about 1.33% (chain pattern) and 2.33% (zig-zag pattern) more maximum load than the lap joint. The simulations showed the same ranking, with the highest equivalent stress of 560.03 MPa obtained for the zig-zag pattern butt joint. Post-test observation showed that all joint variations failed by rivet shear initiated by stress concentration around the rivet holes. Overall, the zig-zag pattern and the butt joint gave a higher tensile capacity than the chain pattern and the lap joint, accompanied by a higher maximum local stress.

Keywords

ANSYS Workbench butt joint chain pattern finite element method lap joint riveted joint stress concentration factor shear stress zig-zag pattern

Citation of this Article

Dwi Basuki Wibowo, Toni Prahasto, Ismoyo Haryanto, Ojo Kurdi, & Khoirul Dimas Veri Anjaswara. (2026). Numerical Analysis and Experimental Study of Shear Stress in Riveted Joints with Variation of Joint Type and Geometric Configuration. Current Journal of Engineering and Science Research. 3(11), 35-40. Article DOI: https://doi.org/10.47001/CJESR/2026.311005 

Licence Copyright (c) 2026 Current Journal of Engineering and Science Research. This work is licensed under a Creative Commons Attribution Non Commercial 4.0 International Licence.

References

  1. F. Delzendehrooy, A. Akhavan-Safar, A. Q. Barbosa, R. Beygi, D. Cardoso, R. J. C. Carbas, E. A. S. Marques, and L. F. M. da Silva, “A comprehensive review on structural joining techniques in the marine industry,” Compos. Struct., vol. 289, Art. no. 115490, 2022.
  2. G. L. Kulak, J. W. Fisher, and J. H. A. Struik, Guide to Design Criteria for Bolted and Riveted Joints. American Institute of Steel Construction (AISC), 2021.
  3. J. Mucha and W. Witkowski, “Mechanical behavior and failure of riveting joints in tensile and shear tests,” Strength Mater., vol. 47, no. 5, pp. 755–769, 2015.
  4. Y. Zhang, J. Zhang, B. Chen, and Y. Zhang, “Shear mechanism of high-strength friction-grip bolts in steel and composite beams,” vol. 9, pp. 1–14, Apr. 2022.
  5. M. Li, W. Tian, J. Hu, C. Wang, and W. Liao, “Study on shear behavior of riveted lap joints of aircraft fuselage with different hole diameters and squeeze forces,” Eng. Fail. Anal., Art. no. 105499, 2021.
  6. I.Giorgobiani, “Optimal modelling of rivet joints using finite element method,” 2020.
  7. V. B. Bhandari, Machine Design Data Book. New Delhi, India: McGraw-Hill Education, 2015.
  8. C. Sinthusiri and S. A. Nassar, “Load distributions in bolted single lap joints under non-central tensile shear loading,” J. Adv. Join. Process., vol. 3, Art. no. 100055, 2021.
  9. B. Suwasono, M. Rizal, N. Y. Nugroho, and D. Hardianto, “Analisis kekuatan butt joint dan lap joint pada pengelasan konstruksi kapal,” vol. 16, no. 2, pp. 243–249, 2023.
  10. K. B. Layuk, A. Kasa, and B. Tangaran, “Pengaruh geometri paku keling terhadap kinerja sambungan pada struktur rangka baja,” Paulus Mech. Eng. J., vol. 3, no. 1, pp. 14–17, 2025.
  11. G. Saputro, M. A. Rizza, U. S. Amrullah, and P. N. Malang, “Simulation analysis of riveted joint specimen with parameter of working pressure and hole clearance using semi-automatic riveting tool,” vol. 2, no. 1, 2023.
  12. R. P. Wirabuana and D. B. Wibowo, “Analisis kekuatan paku keling pada sub-assembly kampas rem bus,” J. Tek. Mesin S-1, vol. 3, no. 1, pp. 38–43, 2015.
  13. G. Saritha, T. Iswarya, D. Keerthana, and A. T. D. Baig, “Micro universal testing machine system for material property measurement,” Mater. Today Proc., 2023.
  14. R. G. Budynas and J. K. Nisbett, Shigley’s Mechanical Engineering Design, 10th ed. New York, NY, USA: McGraw-Hill Education, 2015.