Volume 3, Issue 11, November 2026

Current Journal of Engineering and Science Research · ISSN (online): 3049-1738

Open Access Peer Reviewed

Published Articles

Design and Development of a SCADA Program for Substations Based on Matlab App Designer and Simulink

Nguyen Thi My Nguyen Nguyen Duong Sang Dang Truong Quoc Hao Vo Ngoc Hai Nguyen Anh Thi Ngo Minh Khoa

Volume 3, Issue 11, Pages 1-8, November 2026

This paper presents a method for designing a substation SCADA application based on MATLAB/Simulink integrated with MATLAB App Designer. The substation simulation model is constructed using Simscape Electrical, comprising key components such as grid sources, power transformers, busbars, transmission lines, circuit breakers, disconnectors, and measurement devices. The SCADA software is develop... Read More

Article DOI:  doi.org/10.47001/CJESR/2026.311001

Mechanical Properties and Failure Behavior of GMAW-Welded SS400 Carbon Steel after Immersion in Sulfuric Acid Solution

Yusuf Umardani Agus Suprihanto Dani Dwi Prasetyo

Volume 3, Issue 11, Pages 9-15, November 2026

The mechanical integrity of welded carbon steel exposed to acidic environments depends on weld-zone heterogeneity, local hardness characteristics, and joint discontinuities. This study evaluates the changes in Vickers microhardness and tensile strength of gas metal arc welded (GMAW) SS400 carbon steel after immersion in 0.5 M sulfuric acid (H₂SO₄). Four exposure conditions were considered... Read More

Article DOI:  doi.org/10.47001/CJESR/2026.311002

CFD Investigation of the Effects of Wind Speed and Duct Geometry on the Performance of a Ducted Wind Turbine for Energy Efficiency

Nazaruddin Sinaga Dwi Basuki Wibowo Rendy Augustino Sam

Volume 3, Issue 11, Pages 16-25, November 2026

Indonesia holds considerable wind energy potential, yet its prevailing wind speeds of roughly 2–6 m/s make it difficult for conventional turbines to operate near their optimum. Diffuser-augmented (ducted) wind turbines offer a promising remedy by accelerating the flow through the rotor plane. This study uses computational fluid dynamics (CFD) to examine how inlet wind speed, diffuser expans... Read More

Article DOI:  doi.org/10.47001/CJESR/2026.311003

An Audit of Temporal and Acquisition Confounds in the TON_IoT Telemetry Datasets

Reginald Ekene Ogu

Volume 3, Issue 11, Pages 26-34, November 2026

The TON_IoT telemetry files, covering seven IoT and IIoT devices, are widely used to train and compare attack detectors, and many studies report near-perfect accuracy on these files. This audit asks what those scores measure. Each device file was examined for class timing, sampling behaviour, value encoding and information content. Classifiers were then trained on sensor values, timestamp fea... Read More

Article DOI:  doi.org/10.47001/CJESR/2026.311004

Numerical Analysis and Experimental Study of Shear Stress in Riveted Joints with Variation of Joint Type and Geometric Configuration

Dwi Basuki Wibowo Toni Prahasto Ismoyo Haryanto Ojo Kurdi Khoirul Dimas Veri Anjaswara

Volume 3, Issue 11, Pages 35-40, November 2026

Riveted joints are still widely used in steel structures because of their good resistance to mechanical loading, and their performance is governed by the joint type and the rivet geometric configuration. This study investigates the effects of joint type (lap joint and butt joint) and rivet configuration (chain pattern and zig-zag pattern) on the mechanical behavior of AISI 1020 steel riveted ... Read More

Article DOI:  doi.org/10.47001/CJESR/2026.311005